Matters needing attention in operation and daily maintenance of sealing machine-hand-push type of Putian hot melt adhesive sealing machine

Matters needing attention in operation and daily maintenance of sealing machine-hand-push type of Putian hot melt adhesive sealing machine

The sealing machine consists of a frame, a speed reduction and speed regulation transmission mechanism, a sealing and printing mechanism, a conveying device and an electrical electronic control system. When the power supply is turned on, all the mechanisms start to work, and the electric heating elements are heated after being turned on, so that the upper and lower heating blocks are heated up sharply and adjusted to the required temperature by the temperature control system, the impression wheel rotates, the cooling system starts to cool as needed, the conveyor belt is rotated and adjusted to the required speed by the speed regulating device. -Putian hot melt adhesive box sealing machine hand push type

　　

　　When the package containing articles is placed on the conveyor belt, the sealing part of the bag is automatically sent between the two running sealing belts and brought into the heating zone. The heat of the heating block is transferred to the sealing part of the bag through the sealing belts, so that the film is heated and melted, and then passes through the cooling zone, so that the surface temperature of the film is appropriately reduced. Then, it is rolled by a Hua Lun (or a printing wheel) to bond the upper and lower plastic films on the sealing part and press out a net pattern (or print a logo). Then, the rubber belt and the conveyor belt will seal the film.

　　

　　First, the process operation method

　　

　　1. Press the "ON" button, the power indicator light and "COOLER" (cooling indicator light) light up, and the warning light flashes.

　　

　　2. Press the "START" button, the warning light will go out, the "Start" indicator light will be on, and the power will achieve the preset setting.

　　

　　3. Turn on the power supply of the conveyor belt, run the conveyor belt, and adjust the speed knob to a proper position.

　　

　　4. Push in the container to be sealed and start normal operation.

　　

　　5. If overcurrent occurs during operation, the "FAULT" light on the control panel lights up and the warning light flashes. Press the "RESET" button at this time, and then press the "START" button again after the overcurrent light goes out. -Putian hot melt adhesive box sealing machine hand push type

　　

　　6. When the work is finished, press the "STOP" key, and the machine will return to the 1 state.

　　

　　7. Press the "OFF" key to turn off the machine and exit the standby state.

　　

　　Second, the operation process matters needing attention and daily maintenance

　　

　　1. This machine uses 220V single-phase three-wire power supply, so the grounding must be reliable, otherwise personal safety will be affected.

　　

　　2. Metal parts should not be close to the induction head.

　　

　　3, often check the cooling water level, general frequent use, check once a week, and add cooling water. Use non-conductive cooling water.

　　

　　4, often check the pipeline, joint can't have water leakage, water seepage phenomenon. In order to prevent the pipeline from freezing due to low temperature, antifreeze should be injected into the water tank.

　　

　　5, maintenance should follow the operating sequence.

　　

　　6, maintenance should be fixed professionals.

　　

　　7, after the boot is not allowed to open the chassis, inspection and maintenance must cut off the total power supply.

　　

　　8. The machine is designed with overload and overheating protection system. When the temperature of the radiator plate exceeds 70 degrees, the high voltage will be cut off, and the warning light will flash: when the load is too large (that is, the diameter of the heated bottle caps is too large or closely arranged or too close to the induction head), the high voltage current of the machine will be temporarily overloaded (the digital display instantly exceeds "100"), which can also be protected. This is a normal phenomenon, and you can press the "START" key again to start. -Putian hot melt adhesive box sealing machine hand push type